Showing results: 16 - 30 of 95 items found.
-
ECOPIA
Permanent magnet - Neodium materials - +/- 0.03Tesla deviation can be made in a process of assembling magnet. - However, we indicates correct tesla strength measured by gaussmeter, before shipping magnet kit.
-
HEM -
TOEI INDUSTRY CO, LTD.
The physical quantity of Hall Coefficient, Hall Mobility and Carrier Density etc. can be investigated by measuring at room temperature voltage occurred perpendicularly to the both magnetic field and constant-current when flowing constant-current perpendicularly to magnetic field from current source while applying magnetic field to sample set at the center of magnetic field of magnet.
-
300 Series -
Integrity Design and Reseach Corp.
Typical Applications include Measurements of the Earth's field vectors, Air shipment inspection, Mapping and recording field perturbations, Magnet classification, Analysis of magnetic circuitry and components, Magnetic Resonance Imaging (MRI) and Measuring residual fields.
-
Magna-Mike 8600 -
Olympus Corp.
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
McLAREN Applied Technologies
The output of the Rotary Hall-effect sensor is a voltage which changes in direct proportion to the shaft angle. The sensor is non-contact, using Hall elements to determine the angle of a magnet. The magnet is either mounted in a shaft integral to the sensor or can be mounted externally to the sensor.
-
HMS-5500 -
ECOPIA
Variable temp : 80K ~ 350K (model# : AMP55T ) - HMS-5500 can be compatibly used with both low temp magnet kit (model# :AMP55T) and high temp magnet kit (model#: AHT55T5, upto 500dC) - Below image is to show model# HMS-5500 + AMP55T, for low temp.
-
HMS-5300 -
ECOPIA
Variable temp : 80K ~ 350K (model#: AMP55T ) - HMS-5300 can be compatibly used with both low temp magnet kit (model# : AMP55T) and high temp magnet kit (model# : AHT55T3, upto 300dC). - Below image is to show model# HMS-5300 + AMP55T, for low temp.
-
HMS-5000 -
ECOPIA
Constant current source + Van der Pauw method terminal conversion system
-
AYA-Instruments
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
CYHCT-WS3 -
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Vektrex Electronic Systems
Isolated Hall Effect current sensors provide accurate high bandwidth current sensing. Vektrex offers models to 320A. For use, the 50-ohm voltage output is connected directly to an oscilloscope or data acquisition system. VCS sensors are magnetically isolated like clamp-on oscilloscope probes. With secure cable attachment, repeatability is ensured.
-
CP 35 -
GMC-I-PROSyS
The CP 35 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
CYHCT-L20K -
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-L20K is based on open loop principle and designed with a high galvanic isolationbetween primary conductor and secondary circuit. It can be used for measurement of DC current, DCpulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor
-
ECOPIA
Super high temperature hall effect measurement system that is useful to flow gas into chamber with sample. - Newly developed furnace that makes it possible to increase over 800 and use for measuring hall effect. - Gas flow control system in order to flow various gas. - Sample holder for high temperature. (keep the good contact on 800) - High Temperature control system (DC power) On condition of specific temperature with gas flow , new semiconductor materials have been developed to see electrical property's change.
